null

Metal Sales - Roofing and Wall Trim

  • Track Cover 10'6" - 29 ga. - Trim

    Track Cover 10'6" - 29 ga. - Trim

    This trim is used to cover track for sliding doors. The cover protects the slider from the weather and you can get them in the length you need it. Sliding doors are normally used with residential, commercial and agricultural buildings.Trim is 29 gauge...

    $26.98
    Choose Options
  • W-Valley 10'6" - 29 ga. - Trim

    W-Valley 10'6" - 29 ga. - Trim

    W-Valley Trim is designed to keep the valleys of your roof dry. The long, flat legs on each side fit up under your roof panels. The inverted "V" in the center helps keeps running water and debris in the center of the valley, away from the panel ends. The...

    $41.26
    Choose Options
  • Notched Gambrel 41" - 29 ga. - Trim

    Notched Gambrel 41" - 29 ga. - Trim

    FLASHING for GAMBREL roofThis is our standard size 41” trim.  Please note: if you need a custom size of this trim please contact us!• Available in colors that match the roof or wall panel• 29-Gauge steel material• Energy Star listed finish...

    $8.81
    Choose Options
  • Gambrel Trim 10' - 29 ga. - Trim

    Gambrel Trim 10' - 29 ga. - Trim

    FLASHING for GAMBREL roofThis is our standard size 10 ft trim. You need to order the trim with the right pitch for your roof or connection.• Available in colors that match the roof or wall panel• 29-Gauge steel material• Energy Star listed...

    $17.35
    Choose Options
  • Peak Trim 10'6" - 29 ga. - Trim

    Peak Trim 10'6" - 29 ga. - Trim

    Length = 10 feet 6 inchesGirth = 11 inchesMade to specified angle• Available in colors that match the roof or wall panel• 29-Gauge steel material• Energy Star listed finish that is mildew resistant and will not warp, rot or absorb...

    $18.83
    Choose Options
  • Notched Endwall 41" - 29 ga. - Trim

    Notched Endwall 41" - 29 ga. - Trim

    Notched endwall trim is used for attaching a lean-to, roof or similar to a wall. This is a flashing to make the transition from the wall to the roof, so there are no leaks at the connection. You need to order the trim with the right pitch for your roof...

    $8.81
    Choose Options
  • Endwall Flashing 10'6" - 29 ga. - Trim

    Endwall Flashing 10'6" - 29 ga. - Trim

    Endwall flashing trim is used for attaching a lean-to, roof or similar to a wall. This is a flashing to make the transition from the wall to the roof, so there are no leaks at the connection. You need to order the trim with the right pitch for your roof...

    $21.94
    Choose Options
  • Universal Sidewall 10'6" - 29 ga. - Trim

    Universal Sidewall 10'6" - 29 ga. - Trim

    Universal Sidewall Trim is designed to flash from your metal roof panels to a vertical wall, such as a chimney. Striations and bends on the flashing provide strength and match the lines of your other edge trims. The Universal Sidewall Trim, combined with...

    $16.21
    Choose Options
  • Transition Flashing 10'6" - 29 ga. - Trim

    Transition Flashing 10'6" - 29 ga. - Trim

    Transition flashing trim is used for attaching a lean-to, roof or similar to a building – same level as the roof. This is a flashing to make the transition from the building roof to the lean to roof, so there is no leaks at the connection. You need to...

    $36.03
    Choose Options
  • Universal Endwall 10'6" - 29 ga. - Trim

    Universal Endwall 10'6" - 29 ga. - Trim

    Universal End wall Trim is designed to flash from the high side of the metal roof panels to a vertical wall, such as the front of a dormer. Striations and bends on the flashing provide strength and match the lines of your other edge trims. The Universal...

    $17.35
    Choose Options
  • C&T Trim 10'6" - 29 ga. - Trim

    C&T Trim 10'6" - 29 ga. - Trim

    C&T trim is used when you have metal panel siding going up against a metal panel ceiling – this trim piece gives an trim to the edge of the ceiling and the wall. You can order the trim in any colors. The application is normally used for interior of...

    $23.05
    Choose Options
  • F&J Channel 10'6" - 29 ga. - Trim

    F&J Channel 10'6" - 29 ga. - Trim

    F&J trim is used to connect sidewall metal panels with soffit that is under an overhang. The soffit fits into the gap of the trim, and so do the sidewall metal. This trim will come in the same colors available as the side metal panels. You can also...

    $19.90
    Choose Options
  • F-Channel 10'6" - 29 ga. - Trim

    F-Channel 10'6" - 29 ga. - Trim

    F -channel is used for lean-to or pavilions where you don’t have side metal. The trim will hold the soffit and trim it out.• Available in colors that match the roof or wall panel• 29-Gauge steel material• Energy Star listed finish that is...

    $14.88
    Choose Options
  • J-Channel 10'6" - 29 ga. - Trim

    J-Channel 10'6" - 29 ga. - Trim

    J-channel flashing is designed specifically for trimming out openings on your wall panels. Windows, doors, and louvers on the walls of your building blend in seamlessly when j-channel is installed. J-channel hides the cut lines or edges of wall panels...

    $7.30
    Choose Options
  • 1.5" x 1.5" Angle 10' - 29 ga. - Trim

    1.5" x 1.5" Angle 10' - 29 ga. - Trim

    Angle trim is used as drip edge in combination with the post trim on facia board. Its used to make a complete cover for the facia and transition from the roof.• Available in colors that match the roof or wall panel• 29-Gauge steel...

    $7.95
    Choose Options
  • Drip Cap 10'6" - 29 ga. - Trim

    Drip Cap 10'6" - 29 ga. - Trim

    Drip cap is used over windows and doors to give the water a way to drip off without damaging anything. • Available in colors that match the roof or wall panel• 29-Gauge steel material• Energy Star listed finish that is mildew resistant and...

    $15.37
    Choose Options
  • Double Angle 10'6" - 29 ga. - Trim

    Double Angle 10'6" - 29 ga. - Trim

    Double Angle trim is used for transition from one wall metal to another – where you have a split of the side metal panels. The trim gives base for the upper metal and a flashing behind it, and the bottom metal will sit inside the J so it looks trimmed...

    $9.28
    Choose Options
  • Base Angle 10'6" - 29 ga. - Trim

    Base Angle 10'6" - 29 ga. - Trim

    Base Angle is often also called Rat Guard trim, and standard length is 10.6 Ft. Base Angle, is installed at the base of walls. It gives a base for the wall metal panels and t give flashing up behind the metal.• Available in colors that match the...

    $9.28
    Choose Options